TJ-POD Series
Powder brake pictures:
Magnetic powder clutch and brake working principle
The magnetic powder clutch is composed of active rotor(input shaft), driven rotor(output shaft) and yoke with excitation coil. The three parts are resembled against the concentric part and form a system which can rotate relatively. The annular gap between active rotor and driven rotor is full of alloy powder which has high permeability.
The magnetic powder will be in the state of loose when the current do not pass the excitation coil. The magnetic powder will be thrown on the inner wall of active rotor. In this case, there will not exist the interaction force between the active and driven rotor. Because the magnetic powder clutch is in the state of separation, no torque transmission exits.
The magnetic powder in the working chamber will link in a link state under the action of the magnetic flux generated from the Yoke when the current pass the excitation coil. The magnetic powder clutch can transfer torque relying on the shear force generated from magnetic chain and the friction generated from the magnetic powder and working face. In this case, the magnetic powderclutch is in the state of combination.
When the current is cut off, the magnetic flux will disappear with the disappearance of the magnetizing current, the magnetic powder will be in the state of loose under the action of gravity again, and will be thrown on the inner wall of active rotor under the action of the centrifugal force. In this case, the magnetic powder clutch will be in the state of separation again.
The magnetic powder clutch and brake have the same principle, the magnetic powder brake will form as long as the driven rotor of the magnetic powder clutch is fixed.
Features:
The magnetizing current has a linear relation with torque
As is shown in chart 3, the transmission torque has a linear relationship with the magnetizing current. The size of the torque can tet controlled within larger range. Under normal circumstance, the magnetizing current has a linear relationship with transitive torque within range of 5%-100% rated torque.
Stable slip torque
The slip rotational speed between driven rotor and active rotor do not affect the transitive torque when the magnetizing current retain constant , as shown in the chart 4. That is to say, the static friction torque and the dynamic friction torque have no difference.Therefore, the torque can retain constant stably.The features are applied to tension control, users can control the tension of the roll material effectively as long as the regulating the magnetizing current accurately.
Prevention of the phenomenon of heat since slip
The friction part will generate heat inevitably or even destroyed when it keep continuous sliding.But this device has a complete cooling set, it will not generate a lot of heat after long time running and it has a long service life.
Magnetic Powder Brake Notes
1.Don’t overload, meanwhile cool to appropriate temperature
The value of the torque/rotational speed/slip power should be less than the rated value. The cooling mode(natural cooling/forced air cooling/water cooling) should depend on the maximum slip power when it works and the cooling air should pass the water and oil filter. The temperature detector and the alarm should be installed to prevent high temperature which can affect the service life of the magnetic powder.(the highest temperature is 80 degree)
2. Concerning the service life
The life of the magnetic powder clutch and brake rely on the life of the magnetic powder. Generally speaking, its service life is 4500-7500hours in the state of non overloaded; but its service life can extend several times in some cases, such as: the working torque of the magnetic powder clutch/brake,relative slip rotational speed and slip power can be reduced to 50%-70% of the rated value. This is to say, the margin can be enlarged as soon as possible when designing.
Magnetic powder brake installation:
Related Products
Packaging & Shipping
Advantages
Why do you choose us?
Your choice,We promise!
Eight reasons to choose us:
1. Perfect service system and after-sale protection.
2. Quality problems will be solved within 24hours.
3. One-to-one customer service tracking processing.
4. Companies carry out the ERP management, improve enterprise fast response.
5. Quality assurance, one year warranty.
6. Supporting professional matched other equipments.
7. The company has more than one product testing units, the implementation of ISO9001: 2015.
8. Unique development and design capabilities to meet the needs of special-purpose equipment manufacturing.
Five Core strengths:
1. The first domestic independent R & D manufacturer and 13 years of professional manufacturing.
2. Casting exquisite, beautiful, practical and durable.
3. Complete specifications, cost-effective and spot supply.
4. Independent research and development, special specifications can be customized.
5. Selected materials, high-tech treatment, up to the international standard test.
More concerned for our products , please do not hesitate to inquiry now!